Looking for exceptional sound over IP? The 4430A offers power, audio and loudspeaker management via a single standard CAT cable, delivering unrivalled flexibility, cost-effectiveness and simplicity of installation.
4430A
Smart IP Installation Speaker
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_spl.png?)
SPL
104 dB
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_amp_power.png?)
Amplifier Power
50 W Bass (Class D) + 50 W Treble (Class D)
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_frequency_response.png?)
Frequency Response
45 Hz - 39 kHz (-6 dB)
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_accuracy_frequency.png?)
Accuracy of Frequency Response
± 1.5 dB (58 Hz - 20 kHz)
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_driver.png?)
Driver Dimensions
⌀ 130 mm Woofer + ⌀ 19 mm Tweeter (view in inches)
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_dimensions.png?)
Dimensions
H 285 x W 189 x D 178 mm, (view in inches)
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_weight.png?)
Weight
5.1 kg / 11.2 lb
![](/o/genelec-site-theme/images/icons/tech_specs/specs_icon_connectors.png?)
Connections
1 x RJ45 AES67 / Dante Input
1 x Euroblock Analog Input
4430A Smart IP Installation Speaker
Technical Specifications
Looking for exceptional sound over IP? The 4430A offers power, audio and loudspeaker management via a single standard CAT cable, delivering unrivalled flexibility, cost-effectiveness and simplicity of installation.
![](http://images.ctfassets.net/4zjnzn055a4v/3b0NTRfnMmrAhl1kFJ6I5S/7f0bd65e0fac84317c86d08c21effd80/4030CMM-k01.jpg?w=300)
System Specifications
Frequency Response
58 Hz - 20 kHz (± 1.5 dB)
Low cutoff -6dB
45 Hz
High cutoff -6dB
39 kHz
SPL
Peak SPL Maximum peak acoustic output per unit in a listening room with music material, at 1 m, using PoE+ power.
≥107 dB
Short term max SPL Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz at 1 m.
≥104 dB
Long term max SPL Maximum long term RMS acoustic output in same conditions with IEC weighted noise (limited by driver unit protection circuit) at 1 m.
≥96 dB
Self-generated noise
Self-generated noise Self generated noise level in free field at 1m on axis(A-weighted).
≤5 dB
Weight
Weight5.1 kg (11.2 lb)
Dimensions
Height
285 mm
Width
189 mm
Depth
178 mm
![](http://images.ctfassets.net/4zjnzn055a4v/5mc0284GZiak2gSwwia0SO/22a0eb2ba3a530026c2d6df54d0e65f5/4030c_views.png?w=800)
Enclosure
Enclosure material
Die cast aluminium
Enclosure type
Reflex port
Drivers
Driver type
Cone
Diameter
130 mm
Driver type
Metal dome
Diameter
19 mm
Directivity
![](http://images.ctfassets.net/4zjnzn055a4v/12NLgOi0UZXkDGBzEU2fTI/7a88fadf3f6fe72f366894c76b79daca/4430A_vertical_directivity.png?w=600)
![](http://images.ctfassets.net/4zjnzn055a4v/6Y2rcwPkTBRQvfWdlWeJhC/e7bcd2e42b9e0260b92142d9726b8a72/4430A_horizontal_directivity.png?w=600)
Harmonic distortion
> 200 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
2.3 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
![](http://images.ctfassets.net/4zjnzn055a4v/3ADOnlDnDO0f3ycUcoQyhy/a9004f31faba1cc8d217908ec2e610f8/4430A_GD.jpg?w=800)
Amplifier Section
Amplifiers
50 W Class D
50 W Class D
Mains voltage
PoE+/PoE
Power consumption
ISS Active
≤4 W
Idle
≤5 W
Full output
25.5 W
Signal processing section
Connectors
Input Ethernet (Power over Ethernet and Audio over IP)
Input Audio input is via a 10 kOhm balanced connector.
Crossover
Bass/Treble
2900 Hz