Technical Specifications
SPL
104 dB
Amplifier Power
50 W Bass (Class D) + 50 W Treble (Class D)
Frequency Response
45 Hz - 23 kHz ("-6 dB")
Accuracy of Frequency Response
± 1.5 dB (58 Hz - 20 kHz)
Driver Dimensions
⌀ 130 mm Bass + ⌀ 19 mm Treble (view in inches)
Dimensions
H 299 x W 189 x D 178 mm, with Iso-Pod™ (view in inches)
Weight
5.5 kg / 12.1 lb
Connections
1 x XLR Analog Input
1 x RJ45 AES67 Input
2 x RJ45 Control
8430A
IP SAM™ Studio Monitor
Technical Specifications
The 8430A is the world’s first AoIP studio monitor, allowing reference-quality monitor performance to integrate directly into your IP workflow.
The 8430A was in production between 2016 and 2023.
System Specifications
Frequency Response
58 Hz - 20 kHz (± 1.5 dB)
Low cutoff -6dB
45 Hz
High cutoff -6dB
23 kHz
SPL
Peak SPL
≥110 dB
Maximum peak acoustic output per pair, 1 m distance with music material.
Short term max SPL
≥104 dB
Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz.
Long term max SPL
≥96 dB
Maximum long term RMS acoustic output in same conditions with IEC weighted noise (limited by driver unit protection circuit).
Self-generated noise
Self-generated noise
≤5 dB SPL
Self generated noise level in free field on axis (A-weighted).
Weight
Weight5.5 kg (12.1 lb)
Dimensions
Height
285 mm
(11 1/4 in)
Height with Iso-Pod
299 mm
(11 3/4 in)
Width
189 mm
(7 1/2 in)
Depth
178 mm
(7 in)
Enclosure
Enclosure material
Die cast aluminium
Enclosure type
Reflex port
Drivers
Driver type
Cone
Diameter
130 mm
(5 1/8 in)
Driver type
Metal dome
Diameter
19 mm
(3/4 in)
Directivity
Harmonic distortion
> 100 Hz ≤0.5 %
Group delay
The latency at high frequencies from the input to the acoustic output, measured in the analog input:
Extended Phase Linearity in GLM set to OFF
2.3 ms
In Genelec performance graphics, the time of converting the from an electronic input signal to the acoustic output in a Genelec monitor is described by two factors – latency and group delay. The group delay factor can be read in the graphics for a specific frequency. The total frequency-specific input-to-output delay is a sum of the latency and group delay factors. To understand the significance of this total delay, consider that moving a loudspeaker away by 1 meter creates an additional delay of about 3 ms.
Amplifier Section
Amplifiers
50 W Class D
Bass amplifier short term output power.
50 W Class D
Treble amplifier short term output power.
Mains voltage
100-240 VAC 50/60Hz
Power consumption
ISS Active
≤0.5 W
Idle
≤3 W
Full output
50 W
Signal processing section
Connectors
Input
Analog signal input connector XLR female, balanced 10 kOhm.
Input
Audio-over-IP format and input connector:
- AES67 and RAVENNA
- RJ45 connector with or without an XLR shell
- Fast Ethernet 100BASE-TX (IEEE 802.3)
2 x Control
Two CAT5 (RJ45) GLM Network connectors for computer control using the Genelec Loudspeaker Manager (GLM) software.
